Some EMC targets will fail if we advertise that we can authenticate with
CHAP, but the target is configured to allow unauthenticated access to that
target. We advertise AuthMethod=CHAP,None; the target should (I think)
select AuthMethod=None for unprotected targets. IETD does this, but an
EMC Celerra NS83 doesn't.
Fix by offering only AuthMethod=None if the user hasn't supplied a
username and password; this means that we won't be offering CHAP
authentication unless the user is expecting to use it (in which case the
target is presumably configured appropriately).
Many thanks to Alessandro Iurlano <alessandro.iurlano@gmail.com> for
reporting and helping to diagnose this problem.
ROMs will refuse to build unless pci_vendor_id and pci_device_id are
defined. We probably ought to fix up the Makefile (and the ROM prefix) so
that they're required only for PCI ROMs, but this will do for now.
Drivers are not allowed to call printf(). Converted eprintf() to DBG(),
and removed spurious startup banner.
Fixed hardcoded inclusion of little_bswap.h
Use EIO rather than 1 as an error number.
Add ability for network devices to flag link up/down state to the
networking core.
Autobooting code will now wait for link-up before attempting DHCP.
IPoIB reflects the Infiniband link state as the network device link state
(which is not strictly correct; we also need a succesful IPoIB IPv4
broadcast group join), but is probably more informative.
Infiniband devices no longer block waiting for link-up in
register_ibdev().
Hermon driver needs to create an event queue and poll for link-up events.
Infiniband core needs to reread MAD parameters when link state changes.
IPoIB needs to cope with Infiniband link parameters being only partially
available at probe and open time.
PXE is a catch-all image format with no signature checks. If an
unsupported image file is loaded, it will be treated as a PXE image. In
most cases, the image will be too large to be loaded as a PXE image (which
has to fit in base memory), so the error returned to the user will be that
the segment could not fit within the memory region.
Add an explicit check to pxe_image.c to reject images larger than base
memory with ENOEXEC.
Add ENOEXEC to the error string table.
gPXE is not compliant with the HTTP/1.1 specification (RFC 2616),
since it lacks support for "Transfer-Encoding: chunked". gPXE is,
however, compliant with the HTTP/1.0 specification (RFC 1945), which
does not require "Transfer-Encoding: chunked" to be supported.
The only HTTP/1.1 feature that gPXE uses is the "Host:" header, but
servers universally accept that one from HTTP/1.0 clients as an
optional extension (it is obligatory for HTTP/1.1). gPXE does not,
for example, appear to support connection caching. Advertising as a
HTTP/1.0 client will typically make the server close the connection
immediately upon sending the last data, which is actually beneficial
if we aren't going to keep the connection alive anyway.
The PXE spec is (as usual) unclear on precisely when ProxyDHCPREQUESTs
should be issued. We adapt the following, slightly paranoid approach:
If an offer contains an IP address, then it is a normal DHCPOFFER.
If an offer contains an option #60 "PXEClient", then it is a
ProxyDHCPOFFER. Note that the same packet can be both a normal
DHCPOFFER and a ProxyDHCPOFFER.
After receiving the normal DHCPACK, if we have received a
ProxyDHCPOFFER, we unicast a ProxyDHCPREQUEST back to the ProxyDHCP
server on port 4011. If we time out waiting for a ProxyDHCPACK, we
treat this as a non-fatal error.
Change the PXE return code for EWOULDBLOCK from PXENV_STATUS_FAILURE
to PXENV_STATUS_TFTP_OPEN. This code is only used by the FILE_READ
PXEXT call, and is necessary to distinguish "error" from "no data" in
that call.
(The only other nonblocking call is UDP_READ, where the caller doesn't
care about the distinction, however, gPXE doesn't use EWOULDBLOCK
internally to represent this condition in that code.)
Allow for settings to be described by something other than a DHCP option
tag if desirable. Currently used only for the MAC address setting.
Separate out fake DHCP packet creation code from dhcp.c to fakedhcp.c.
Remove notion of settings from dhcppkt.c.
Rationalise dhcp.c to use settings API only for final registration of the
DHCP options, rather than using {store,fetch}_setting throughout.
Add dedicated functions create_dhcpdiscover(), create_dhcpack() and
create_proxydhcpack() for use by external code such as the PXE preboot
code.
Register ProxyDHCP options under the global scope "proxydhcp".
Unregister previously-acquired DHCP and ProxyDHCP settings when DHCP
succeeds.
Add a configuration settings block for each net device. This will
provide the parent scope for settings applicable only to that network
device (e.g. non-volatile options stored on the NIC, options obtained via
DHCP, etc.).
Expose the MAC address as a setting.
Add the notion of the settings hierarchy, complete with
register/unregister routines.
Rename set->store and get->fetch to avoid naming conflicts with get/put
as used in reference counting.
Add the concept of an abstract configuration setting, comprising a (DHCP)
tag value and an associated byte sequence.
Add the concept of a settings namespace.
Add functions for extracting string, IPv4 address, and signed and
unsigned integer values from configuration settings (analogous to
dhcp_snprintf(), dhcp_ipv4_option(), etc.).
Update functions for parsing and formatting named/typed options to work
with new settings API.
Update NVO commands and config UI to use new settings API.
