250 lines
7.5 KiB
C
250 lines
7.5 KiB
C
/*
|
|
* Copyright (C) 1996-1998 Linus Torvalds & authors (see below)
|
|
*/
|
|
|
|
/*
|
|
* Authors:
|
|
* Jaromir Koutek <miri@punknet.cz>,
|
|
* Jan Harkes <jaharkes@cwi.nl>,
|
|
* Mark Lord <mlord@pobox.com>
|
|
* Some parts of code are from ali14xx.c and from rz1000.c.
|
|
*
|
|
* OPTi is trademark of OPTi, Octek is trademark of Octek.
|
|
*
|
|
* I used docs from OPTi databook, from ftp.opti.com, file 9123-0002.ps
|
|
* and disassembled/traced setupvic.exe (DOS program).
|
|
* It increases kernel code about 2 kB.
|
|
* I don't have this card no more, but I hope I can get some in case
|
|
* of needed development.
|
|
* My card is Octek PIDE 1.01 (on card) or OPTiViC (program).
|
|
* It has a place for a secondary connector in circuit, but nothing
|
|
* is there. Also BIOS says no address for
|
|
* secondary controller (see bellow in ide_init_opti621).
|
|
* I've only tested this on my system, which only has one disk.
|
|
* It's Western Digital WDAC2850, with PIO mode 3. The PCI bus
|
|
* is at 20 MHz (I have DX2/80, I tried PCI at 40, but I got random
|
|
* lockups). I tried the OCTEK double speed CD-ROM and
|
|
* it does not work! But I can't boot DOS also, so it's probably
|
|
* hardware fault. I have connected Conner 80MB, the Seagate 850MB (no
|
|
* problems) and Seagate 1GB (as slave, WD as master). My experiences
|
|
* with the third, 1GB drive: I got 3MB/s (hdparm), but sometimes
|
|
* it slows to about 100kB/s! I don't know why and I have
|
|
* not this drive now, so I can't try it again.
|
|
* I write this driver because I lost the paper ("manual") with
|
|
* settings of jumpers on the card and I have to boot Linux with
|
|
* Loadlin except LILO, cause I have to run the setupvic.exe program
|
|
* already or I get disk errors (my test: rpm -Vf
|
|
* /usr/X11R6/bin/XF86_SVGA - or any big file).
|
|
* Some numbers from hdparm -t /dev/hda:
|
|
* Timing buffer-cache reads: 32 MB in 3.02 seconds =10.60 MB/sec
|
|
* Timing buffered disk reads: 16 MB in 5.52 seconds = 2.90 MB/sec
|
|
* I have 4 Megs/s before, but I don't know why (maybe changes
|
|
* in hdparm test).
|
|
* After release of 0.1, I got some successful reports, so it might work.
|
|
*
|
|
* The main problem with OPTi is that some timings for master
|
|
* and slave must be the same. For example, if you have master
|
|
* PIO 3 and slave PIO 0, driver have to set some timings of
|
|
* master for PIO 0. Second problem is that opti621_set_pio_mode
|
|
* got only one drive to set, but have to set both drives.
|
|
* This is solved in compute_pios. If you don't set
|
|
* the second drive, compute_pios use ide_get_best_pio_mode
|
|
* for autoselect mode (you can change it to PIO 0, if you want).
|
|
* If you then set the second drive to another PIO, the old value
|
|
* (automatically selected) will be overrided by yours.
|
|
* There is a 25/33MHz switch in configuration
|
|
* register, but driver is written for use at any frequency.
|
|
*
|
|
* Version 0.1, Nov 8, 1996
|
|
* by Jaromir Koutek, for 2.1.8.
|
|
* Initial version of driver.
|
|
*
|
|
* Version 0.2
|
|
* Number 0.2 skipped.
|
|
*
|
|
* Version 0.3, Nov 29, 1997
|
|
* by Mark Lord (probably), for 2.1.68
|
|
* Updates for use with new IDE block driver.
|
|
*
|
|
* Version 0.4, Dec 14, 1997
|
|
* by Jan Harkes
|
|
* Fixed some errors and cleaned the code.
|
|
*
|
|
* Version 0.5, Jan 2, 1998
|
|
* by Jaromir Koutek
|
|
* Updates for use with (again) new IDE block driver.
|
|
* Update of documentation.
|
|
*
|
|
* Version 0.6, Jan 2, 1999
|
|
* by Jaromir Koutek
|
|
* Reversed to version 0.3 of the driver, because
|
|
* 0.5 doesn't work.
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/ide.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
#define DRV_NAME "opti621"
|
|
|
|
#define READ_REG 0 /* index of Read cycle timing register */
|
|
#define WRITE_REG 1 /* index of Write cycle timing register */
|
|
#define CNTRL_REG 3 /* index of Control register */
|
|
#define STRAP_REG 5 /* index of Strap register */
|
|
#define MISC_REG 6 /* index of Miscellaneous register */
|
|
|
|
static int reg_base;
|
|
|
|
static DEFINE_SPINLOCK(opti621_lock);
|
|
|
|
/* Write value to register reg, base of register
|
|
* is at reg_base (0x1f0 primary, 0x170 secondary,
|
|
* if not changed by PCI configuration).
|
|
* This is from setupvic.exe program.
|
|
*/
|
|
static void write_reg(u8 value, int reg)
|
|
{
|
|
inw(reg_base + 1);
|
|
inw(reg_base + 1);
|
|
outb(3, reg_base + 2);
|
|
outb(value, reg_base + reg);
|
|
outb(0x83, reg_base + 2);
|
|
}
|
|
|
|
/* Read value from register reg, base of register
|
|
* is at reg_base (0x1f0 primary, 0x170 secondary,
|
|
* if not changed by PCI configuration).
|
|
* This is from setupvic.exe program.
|
|
*/
|
|
static u8 read_reg(int reg)
|
|
{
|
|
u8 ret = 0;
|
|
|
|
inw(reg_base + 1);
|
|
inw(reg_base + 1);
|
|
outb(3, reg_base + 2);
|
|
ret = inb(reg_base + reg);
|
|
outb(0x83, reg_base + 2);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
|
|
{
|
|
ide_hwif_t *hwif = drive->hwif;
|
|
ide_drive_t *pair = ide_get_pair_dev(drive);
|
|
unsigned long flags;
|
|
unsigned long mode = XFER_PIO_0 + pio, pair_mode;
|
|
u8 tim, misc, addr_pio = pio, clk;
|
|
|
|
/* DRDY is default 2 (by OPTi Databook) */
|
|
static const u8 addr_timings[2][5] = {
|
|
{ 0x20, 0x10, 0x00, 0x00, 0x00 }, /* 33 MHz */
|
|
{ 0x10, 0x10, 0x00, 0x00, 0x00 }, /* 25 MHz */
|
|
};
|
|
static const u8 data_rec_timings[2][5] = {
|
|
{ 0x5b, 0x45, 0x32, 0x21, 0x20 }, /* 33 MHz */
|
|
{ 0x48, 0x34, 0x21, 0x10, 0x10 } /* 25 MHz */
|
|
};
|
|
|
|
ide_set_drivedata(drive, (void *)mode);
|
|
|
|
if (pair) {
|
|
pair_mode = (unsigned long)ide_get_drivedata(pair);
|
|
if (pair_mode && pair_mode < mode)
|
|
addr_pio = pair_mode - XFER_PIO_0;
|
|
}
|
|
|
|
spin_lock_irqsave(&opti621_lock, flags);
|
|
|
|
reg_base = hwif->io_ports.data_addr;
|
|
|
|
/* allow Register-B */
|
|
outb(0xc0, reg_base + CNTRL_REG);
|
|
/* hmm, setupvic.exe does this ;-) */
|
|
outb(0xff, reg_base + 5);
|
|
/* if reads 0xff, adapter not exist? */
|
|
(void)inb(reg_base + CNTRL_REG);
|
|
/* if reads 0xc0, no interface exist? */
|
|
read_reg(CNTRL_REG);
|
|
|
|
/* check CLK speed */
|
|
clk = read_reg(STRAP_REG) & 1;
|
|
|
|
printk(KERN_INFO "%s: CLK = %d MHz\n", hwif->name, clk ? 25 : 33);
|
|
|
|
tim = data_rec_timings[clk][pio];
|
|
misc = addr_timings[clk][addr_pio];
|
|
|
|
/* select Index-0/1 for Register-A/B */
|
|
write_reg(drive->dn & 1, MISC_REG);
|
|
/* set read cycle timings */
|
|
write_reg(tim, READ_REG);
|
|
/* set write cycle timings */
|
|
write_reg(tim, WRITE_REG);
|
|
|
|
/* use Register-A for drive 0 */
|
|
/* use Register-B for drive 1 */
|
|
write_reg(0x85, CNTRL_REG);
|
|
|
|
/* set address setup, DRDY timings, */
|
|
/* and read prefetch for both drives */
|
|
write_reg(misc, MISC_REG);
|
|
|
|
spin_unlock_irqrestore(&opti621_lock, flags);
|
|
}
|
|
|
|
static const struct ide_port_ops opti621_port_ops = {
|
|
.set_pio_mode = opti621_set_pio_mode,
|
|
};
|
|
|
|
static const struct ide_port_info opti621_chipset __devinitdata = {
|
|
.name = DRV_NAME,
|
|
.enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
|
|
.port_ops = &opti621_port_ops,
|
|
.host_flags = IDE_HFLAG_NO_DMA,
|
|
.pio_mask = ATA_PIO4,
|
|
};
|
|
|
|
static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
return ide_pci_init_one(dev, &opti621_chipset, NULL);
|
|
}
|
|
|
|
static const struct pci_device_id opti621_pci_tbl[] = {
|
|
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
|
|
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 0 },
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, opti621_pci_tbl);
|
|
|
|
static struct pci_driver opti621_pci_driver = {
|
|
.name = "Opti621_IDE",
|
|
.id_table = opti621_pci_tbl,
|
|
.probe = opti621_init_one,
|
|
.remove = ide_pci_remove,
|
|
.suspend = ide_pci_suspend,
|
|
.resume = ide_pci_resume,
|
|
};
|
|
|
|
static int __init opti621_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&opti621_pci_driver);
|
|
}
|
|
|
|
static void __exit opti621_ide_exit(void)
|
|
{
|
|
pci_unregister_driver(&opti621_pci_driver);
|
|
}
|
|
|
|
module_init(opti621_ide_init);
|
|
module_exit(opti621_ide_exit);
|
|
|
|
MODULE_AUTHOR("Jaromir Koutek, Jan Harkes, Mark Lord");
|
|
MODULE_DESCRIPTION("PCI driver module for Opti621 IDE");
|
|
MODULE_LICENSE("GPL");
|