#!/bin/sh
# this script is used to setup the hypervisor for KVM installations.
# In order for this to work, you have to do the following:
#
# 1.  In your install template, make sure you add the following
#     to your packages list :
#     bridge-utils
#     dnsmasq
#     iscsi-initiator-utils
#     kvm
#     libvirt.x86_64
#     gpxe-kvm
# 
# 2.  In order to get those packaes, you'll need to add the 
#     xCAT-dep repo.  For our test we added the line:
#     repo  --name=xcat-dep --baseurl=http://#TABLE:noderes:$NODE:nfsserver#/install/xcat/xcat-dep/rh5/#TABLE:nodetype:$NODE:arch#
#     This line can be added after the url --url <blah> line
#
#  Once you have that, then the following scripts just set up kvm
#  When the machine boots the first time you'll know it works if you can
#  run the command: 
#  virsh list
#  You'll then see output like:
# Id Name                 State
#----------------------------------




# configure network interfaces for bridging
# here we assume you are using eth0.  Change it if it goes
# somewhere else.
HWETH0=`grep HWADDR /etc/sysconfig/network-scripts/ifcfg-eth0`
HWETH1=`grep HWADDR /etc/sysconfig/network-scripts/ifcfg-eth1`
cat <<EOF > /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
TYPE=Ethernet
ONBOOT=yes
BRIDGE=br0
PROMISC=yes
$HWETH0
EOF
cat <<EOF > /etc/sysconfig/network-scripts/ifcfg-eth1
DEVICE=eth1
TYPE=Ethernet
ONBOOT=no
BOOTPROTO=dhcp
$HWETH1
EOF
cat <<EOF > /etc/sysconfig/network-scripts/ifcfg-br0
DEVICE=br0
TYPE=Bridge
ONBOOT=yes
BOOTPROTO=dhcp
PEERDNS=yes
EOF

#disabled networking code in init.d/kvm
rm -f /etc/libvirt/qemu/networks/*.xml
rm -f /etc/libvirt/qemu/networks/autostart/*.xml
chkconfig --add libvirtd

#added runlevels to init.d/kvm - kvm needs to start before libvirt or the
#libvirt will not recognize kvm-ness is available and vm creation will fail.

cat <<EOF > /etc/init.d/kvm && chmod u+x /etc/init.d/kvm && chkconfig --add kvm
#!/bin/sh
# kvm init script - stripped off bridge code, but still 'Takes care
#
# description: The KVM is a kernel level Virtual Machine Monitor.
start () {
  grep -q GenuineIntel /proc/cpuinfo && /sbin/modprobe kvm-intel
  grep -q AuthenticAMD /proc/cpuinfo && /sbin/modprobe kvm-amd
}
stop () {
  grep -q GenuineIntel /proc/cpuinfo && /sbin/modprobe -r kvm-intel
  grep -q AuthenticAMD /proc/cpuinfo && /sbin/modprobe -r kvm-amd
}
logger -t xcat "KVM $1"
case "\$1" in
  start)
    echo -n $"Starting KVM: "
    logger -t xcat "Starting KVM:"
    start
    echo
    ;;
  stop)
    echo -n $"Shutting down KVM: "
    logger -t xcat "Shutting down KVM:"
    stop
    echo
    ;;
  status)
    echo
    ;;
  *)
    echo "Unknown command: \$1" >&2
    logger -t xcat "Unknown command: \$1"
    echo "Valid commands are: start, stop, status" >&2
    logger -t xcat "Valid commands are: start, stop, status"
    exit 1
esac
EOF


# iscsi target init script
# you may not need this.  Also, you'll have to set the iSCSI target
# leaving this command in shouldn't hurt anything if you don't have
# an iSCSI target

ISCSITARGET=h0.cluster1

cat <<EOF > /etc/init.d/iscsiconnect && chmod u+x
/etc/init.d/iscsiconnect && chkconfig --add iscsiconnect
#!/bin/sh
#
# chkconfig: 345 10 75
# description: iscsi script to discover and connect to targets on boot
connect_targets()
{
  iscsiadm -m discovery -t st -p $ISCSITARGET
  iscsiadm -m node -L automatic
}
disconnect_targets()
{
  iscsiadm -m node --logout
}
logger -t xcat "iscsi $1"
case "\$1" in
    start)
      connect_targets
      ;;
    stop)
      disconnect_targets
      ;;
    status)
      iscsiadm -m node
      ;;
    *)
      echo "Unknown command: \$1" >&2
      logger -t xcat "Unknown command: \$1"
      echo "Valid commands are: start, stop, status" >&2
      logger -t xcat "Valid commands are: start, stop, status"
      exit 1
esac
EOF