217 lines
6.8 KiB
Plaintext
217 lines
6.8 KiB
Plaintext
|
if ETRAXFS
|
||
|
|
|
||
|
|
menu "ETRAX FS options"
|
||
|
|
depends on ETRAXFS
|
||
|
|
|
||
|
|
config ETRAX_DRAM_VIRTUAL_BASE
|
||
|
|
hex
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "c0000000"
|
||
|
|
|
||
|
|
config ETRAX_SERIAL_PORTS
|
||
|
|
int
|
||
|
|
default 4
|
||
|
|
|
||
|
|
config ETRAX_MEM_GRP1_CONFIG
|
||
|
|
hex "MEM_GRP1_CONFIG"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "4044a"
|
||
|
|
help
|
||
|
|
Waitstates for flash. The default value is suitable for the
|
||
|
|
standard flashes used in axis products (120 ns).
|
||
|
|
|
||
|
|
config ETRAX_MEM_GRP2_CONFIG
|
||
|
|
hex "MEM_GRP2_CONFIG"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "0"
|
||
|
|
help
|
||
|
|
Waitstates for SRAM. 0 is a good choice for most Axis products.
|
||
|
|
|
||
|
|
config ETRAX_MEM_GRP3_CONFIG
|
||
|
|
hex "MEM_GRP3_CONFIG"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "0"
|
||
|
|
help
|
||
|
|
Waitstates for CSP0-3. 0 is a good choice for most Axis products.
|
||
|
|
It may need to be changed if external devices such as extra
|
||
|
|
register-mapped LEDs are used.
|
||
|
|
|
||
|
|
config ETRAX_MEM_GRP4_CONFIG
|
||
|
|
hex "MEM_GRP4_CONFIG"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "0"
|
||
|
|
help
|
||
|
|
Waitstates for CSP4-6. 0 is a good choice for most Axis products.
|
||
|
|
|
||
|
|
config ETRAX_SDRAM_GRP0_CONFIG
|
||
|
|
hex "SDRAM_GRP0_CONFIG"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "336"
|
||
|
|
help
|
||
|
|
SDRAM configuration for group 0. The value depends on the
|
||
|
|
hardware configuration. The default value is suitable
|
||
|
|
for 32 MB organized as two 16 bits chips (e.g. Axis
|
||
|
|
part number 18550) connected as one 32 bit device (i.e. in
|
||
|
|
the same group).
|
||
|
|
|
||
|
|
config ETRAX_SDRAM_GRP1_CONFIG
|
||
|
|
hex "SDRAM_GRP1_CONFIG"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "0"
|
||
|
|
help
|
||
|
|
SDRAM configuration for group 1. The default value is 0
|
||
|
|
because group 1 is not used in the default configuration,
|
||
|
|
described in the help for SDRAM_GRP0_CONFIG.
|
||
|
|
|
||
|
|
config ETRAX_SDRAM_TIMING
|
||
|
|
hex "SDRAM_TIMING"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "104a"
|
||
|
|
help
|
||
|
|
SDRAM timing parameters. The default value is ok for
|
||
|
|
most hardwares but large SDRAMs may require a faster
|
||
|
|
refresh (a.k.a 8K refresh). The default value implies
|
||
|
|
100MHz clock and SDR mode.
|
||
|
|
|
||
|
|
config ETRAX_SDRAM_COMMAND
|
||
|
|
hex "SDRAM_COMMAND"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "0"
|
||
|
|
help
|
||
|
|
SDRAM command. Should be 0 unless you really know what
|
||
|
|
you are doing (may be != 0 for unusual address line
|
||
|
|
mappings such as in a MCM)..
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PA_OE
|
||
|
|
hex "GIO_PA_OE"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "1c"
|
||
|
|
help
|
||
|
|
Configures the direction of general port A bits. 1 is out, 0 is in.
|
||
|
|
This is often totally different depending on the product used.
|
||
|
|
There are some guidelines though - if you know that only LED's are
|
||
|
|
connected to port PA, then they are usually connected to bits 2-4
|
||
|
|
and you can therefore use 1c. On other boards which don't have the
|
||
|
|
LED's at the general ports, these bits are used for all kinds of
|
||
|
|
stuff. If you don't know what to use, it is always safe to put all
|
||
|
|
as inputs, although floating inputs isn't good.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PA_OUT
|
||
|
|
hex "GIO_PA_OUT"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00"
|
||
|
|
help
|
||
|
|
Configures the initial data for the general port A bits. Most
|
||
|
|
products should use 00 here.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PB_OE
|
||
|
|
hex "GIO_PB_OE"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00000"
|
||
|
|
help
|
||
|
|
Configures the direction of general port B bits. 1 is out, 0 is in.
|
||
|
|
This is often totally different depending on the product used.
|
||
|
|
There are some guidelines though - if you know that only LED's are
|
||
|
|
connected to port PA, then they are usually connected to bits 2-4
|
||
|
|
and you can therefore use 1c. On other boards which don't have the
|
||
|
|
LED's at the general ports, these bits are used for all kinds of
|
||
|
|
stuff. If you don't know what to use, it is always safe to put all
|
||
|
|
as inputs, although floating inputs isn't good.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PB_OUT
|
||
|
|
hex "GIO_PB_OUT"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00000"
|
||
|
|
help
|
||
|
|
Configures the initial data for the general port B bits. Most
|
||
|
|
products should use 00000 here.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PC_OE
|
||
|
|
hex "GIO_PC_OE"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00000"
|
||
|
|
help
|
||
|
|
Configures the direction of general port C bits. 1 is out, 0 is in.
|
||
|
|
This is often totally different depending on the product used.
|
||
|
|
There are some guidelines though - if you know that only LED's are
|
||
|
|
connected to port PA, then they are usually connected to bits 2-4
|
||
|
|
and you can therefore use 1c. On other boards which don't have the
|
||
|
|
LED's at the general ports, these bits are used for all kinds of
|
||
|
|
stuff. If you don't know what to use, it is always safe to put all
|
||
|
|
as inputs, although floating inputs isn't good.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PC_OUT
|
||
|
|
hex "GIO_PC_OUT"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00000"
|
||
|
|
help
|
||
|
|
Configures the initial data for the general port C bits. Most
|
||
|
|
products should use 00000 here.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PD_OE
|
||
|
|
hex "GIO_PD_OE"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00000"
|
||
|
|
help
|
||
|
|
Configures the direction of general port D bits. 1 is out, 0 is in.
|
||
|
|
This is often totally different depending on the product used.
|
||
|
|
There are some guidelines though - if you know that only LED's are
|
||
|
|
connected to port PA, then they are usually connected to bits 2-4
|
||
|
|
and you can therefore use 1c. On other boards which don't have the
|
||
|
|
LED's at the general ports, these bits are used for all kinds of
|
||
|
|
stuff. If you don't know what to use, it is always safe to put all
|
||
|
|
as inputs, although floating inputs isn't good.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PD_OUT
|
||
|
|
hex "GIO_PD_OUT"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00000"
|
||
|
|
help
|
||
|
|
Configures the initial data for the general port D bits. Most
|
||
|
|
products should use 00000 here.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PE_OE
|
||
|
|
hex "GIO_PE_OE"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00000"
|
||
|
|
help
|
||
|
|
Configures the direction of general port E bits. 1 is out, 0 is in.
|
||
|
|
This is often totally different depending on the product used.
|
||
|
|
There are some guidelines though - if you know that only LED's are
|
||
|
|
connected to port PA, then they are usually connected to bits 2-4
|
||
|
|
and you can therefore use 1c. On other boards which don't have the
|
||
|
|
LED's at the general ports, these bits are used for all kinds of
|
||
|
|
stuff. If you don't know what to use, it is always safe to put all
|
||
|
|
as inputs, although floating inputs isn't good.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PE_OUT
|
||
|
|
hex "GIO_PE_OUT"
|
||
|
|
depends on ETRAX_ARCH_V32
|
||
|
|
default "00000"
|
||
|
|
help
|
||
|
|
Configures the initial data for the general port E bits. Most
|
||
|
|
products should use 00000 here.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PV_OE
|
||
|
|
hex "GIO_PV_OE"
|
||
|
|
depends on ETRAX_VIRTUAL_GPIO
|
||
|
|
default "0000"
|
||
|
|
help
|
||
|
|
Configures the direction of virtual general port V bits. 1 is out,
|
||
|
|
0 is in. This is often totally different depending on the product
|
||
|
|
used. These bits are used for all kinds of stuff. If you don't know
|
||
|
|
what to use, it is always safe to put all as inputs, although
|
||
|
|
floating inputs isn't good.
|
||
|
|
|
||
|
|
config ETRAX_DEF_GIO_PV_OUT
|
||
|
|
hex "GIO_PV_OUT"
|
||
|
|
depends on ETRAX_VIRTUAL_GPIO
|
||
|
|
default "0000"
|
||
|
|
help
|
||
|
|
Configures the initial data for the virtual general port V bits.
|
||
|
|
Most products should use 0000 here.
|
||
|
|
|
||
|
|
endmenu
|
||
|
|
|
||
|
|
endif
|